Faushura Therefore, if you use a PWRU power supply rated at 50 wattsyou will have 26 watts of power left over to run additional Cresnet devices. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Complete the following procedure to attach the ears to the unit. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause xrestron interference manuual radio communications. The port is modem compatible modem and PC cables not included.
|Published (Last):||22 March 2018|
|PDF File Size:||14.7 Mb|
|ePub File Size:||7.47 Mb|
|Price:||Free* [*Free Regsitration Required]|
JoJotaur This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. First-time users will need to establish a user account to fully benefit from all available features.
This may result in a conflict with some equipment and therefore all nine pins should not be used. If power is supplied through Cresnet cabling, ensure the cable is securely plugged into the NET connector. No matter how complex or basic, Crestron control systems are entirely customprogrammable to attain the exact functionality required. Page 28 Crestron Electronics, Inc. Apply solder only to the ends of the twisted wires.
Pressing it alone while the system is running restarts the program. Insufficient power can lead to unpredictable results or damage to the equipment. If this software requires payment for a license, you may make one backup copy of the Software, provided Your backup copy is not installed or used on any CPU. The port is modem compatible modem and PC cables not included.
Page 2 This document was prepared manuwl written by the Technical Documentation department crrstron Loosen the terminal block screws and insert the first leg of kanual bussing strip manua, the first common position of the terminal block. Connect the Device Make the necessary connections as called out in the illustration that follows this paragraph. Therefore, if you use a PWRU power supply rated at 50 wattsyou will have 26 watts of power left over to run additional Cresgron devices.
Particular attention should be given to supply connections other than direct connections to the branch circuit. If rack mounting is not required, rubber feet are provided for tabletop mounting or stacking.
Therefore, if you use a PWRU power supply rated at 50 frestronyou will have 26 watts of power left over to run additional Cresnet devices. In such event, you must destroy all copies of the Software and all of its component parts.
Got it, continue to print. Refer to software release notes or Crestron website for other required Crestron software packages. Bussing Strip Installation The 2-Series integrated dual bus control system is supplied with two brass bussing strips to facilitate commoning linking of multiple terminal block connections. If any part of this Agreement is found void and unenforceable, it will not affect the validity of the balance of the Agreement, which shall remain valid and enforceable according to its terms.
Passthrough Mode enables Viewport access to any serial controlled device on the network. Furthermore, this warranty does not cover any product that has had the serial number or license code altered, defaced, improperly obtained, or removed.
Upload program and firmware. Secure the ear to the unit with three screws from step 1, as shown in the following diagram. Apply power after all connections have been made.
Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. Increase the separation between the equipment and receiver. Tighten the terminal block screws to lock the wire and bussing strip into place.
To prevent the possibility of electrical shorts, it is essential that these conductors do not touch any uninsulated portion of the bussing strip. Crestron shall, at its option, repair or replace or refund the license fee for any Software found defective by Crestron if notified crrstron you within the warranty period. Refer to the diagram following step 3 for a detailed view.
For example, a Cresnet run using 18 AWG Crestron Certified Wire and drawing 20 watts should not have a length creston run more than feet. Danger of explosion if battery is incorrectly replaced. All Crestron certified Cresnet wiring must consist of two twisted pairs. Refer to table at right. These ears must be installed prior to mounting. If power is supplied through an AC adapter, verify the DC output plug is properly attached to the control system and that credtron adapter is securely plugged into an outlet.
You may not reverse engineer, decompile, or disassemble the Software. The following are the minimum recommended software versions for the PC: If Cresnet HP is used for the same run, its length could extend to feet. Connects to Cresnet control network. This warranty shall be the sole and exclusive remedy to the original purchaser. The Cresnet Poll Accelerator effectively increases the network speed, fan-out and device addresses by a factor of maual for each Poll Accelerator added to the system.
Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Under normal conditions, it will last for approximately 10 years. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Either is ideal as the master control processor for a stand-alone boardroom or home theater system and serves equally well slaved to another 2-Series crestroh processor to expand the number of control ports as part of a larger control system.
TOP Related Articles.
Moogubei The Software is licensed and not sold. Tighten the terminal block screws to lock the wire and bussing strip into place. Therefore, if you use a PWRU power supply rated at 50 wattsyou will have 26 watts of power left over to run additional Cresnet devices. If less than four, the strip can be trimmed to size with a pair of scissors or wire snips.
Zolot These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision. Therefore, you must treat the Software like any other copyrighted material, subject to the provisions of this Agreement. Apply power after all connections have been made. Updates may be licensed to You by Crestron with additional or different terms. Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any crestronn, including any implied warranties of merchantability or fitness for a particular purpose.
Crestron CP2E Manuals
All Crestron certified Cresnet wiring must consist of two twisted pairs. Consideration must be given if installed in a closed or multi-unit rack assembly since the operating ambient temperature of the rack environment may be greater than the room ambient temperature. Use care in wiring installations to avoid applying 24 VDC to Cresnet wiring from an AC power pack as crestdon as from a system device that contains its own power supply. In the event that the clock fails, only manyal authorized technician should replace it. This is the entire agreement between Crestron and You relating to the Software and it supersedes any prior representations, discussions, undertakings, communications or advertising relating to the Software. First-time users will need to establish a user account to fully benefit from all available features.
Crestron CP2 Manuals